Home Page
   Articles
       links
About Us    
Traders        
Recipes            
Latest Articles
Hot water for bath with no immersion tank?
Page Previous  1, 2
 
Post new topic   Reply to topic    Downsizer Forum Index -> Energy Efficiency and Construction/Major Projects
Author 
 Message
dpack



Joined: 02 Jul 2005
Posts: 45376
Location: yes
PostPosted: Wed May 18, 16 10:15 pm    Post subject: Reply with quote
    

a dish washer heats a few litres of water in a few mins so it might take quite a long time to heat a bath full.

by the time you have re jigged it all and made sure it is electrically safe it still might not work very well ,it might work but i can think of lots of reasons why something else might be better /safer

i have seen a twin tub used as a water heater for a bath but again tis electric and therefore expensive per bathful compared to gas or a fire

Hairyloon



Joined: 20 Nov 2008
Posts: 15425
Location: Today I are mostly being in Yorkshire.
PostPosted: Thu May 19, 16 1:30 am    Post subject: Re: Hot water for bath with no immersion tank? Reply with quote
    

dpack wrote:
i have used 2 scrap heap challenge ways to have a bath in a wood:

find a suitable spot near a spring so as water can be gravity fed into a bath...

Lightweight. Why not a newton pump in the river?

vegplot



Joined: 19 Apr 2007
Posts: 21301
Location: Bethesda, Gwynedd
PostPosted: Thu May 19, 16 8:17 am    Post subject: Reply with quote
    

I'm with Nick.

Nick



Joined: 02 Nov 2004
Posts: 34535
Location: Hereford
PostPosted: Thu May 19, 16 8:32 am    Post subject: Reply with quote
    

vegplot wrote:
I'm with Nick.




Mutton



Joined: 09 May 2009
Posts: 1508

PostPosted: Sat May 21, 16 10:37 am    Post subject: Reply with quote
    

I fully understand that electricity is definitely not green for heating. I seem to remember that calorie for calorie, if you heat water directly with a fuel and compare that to electricity created by a fuel (as in gas fired power station) then you get about 30% of the heat you would have done if you'd used the gas directly.

However, we've not got main gas. Calor gas is a lot more expensive than mains gas (and I don't want the gas cylinder around either).
This is an indoor bathroom, so fire at the tub - nope.

We have a multi-fuel stove that doesn't heat water. We had a previous bad experience with a rayburn with a back boiler so didn't want to go that way on the hot water. We had too much hot water, even with the fire shut down and ashed over, on a windy night the system would boil and usually about 2am we had to get up to deal with it, having been woken by the thunder of pipes and the fun sound of steam jetting into the header tank.

So our long term plan, is DIY solar hot water. Our short term is having an occasional bath as a treat for sore muscles, with an electric heating system, at least as a top up. Will make a start with heating kettles on the top of the multi-fuel (in winter) and then use the electric shower and then having *something* to finish off, and to keep it warm while soaking. Hence the dishwasher pump idea. Do take on board that it is only for small quantities of water, so maybe not quite so clever after all.

If someone can suggest a heater and circulator that is small, that would be really helpful. Small as in fit under a bath. So can fill the bath with warm water (that may or may not be hot enough) and then top up the heating with a little circulating heater.

dpack



Joined: 02 Jul 2005
Posts: 45376
Location: yes
PostPosted: Sat May 21, 16 12:17 pm    Post subject: Reply with quote
    

if you have a spare chimney or space for a flue would a "copper" such as found in old style scullerys fit the bill?

heat water with a fire and use a small pump to get it to the bath tub

a few examples

i can see no reason such a thing could not even be outside so long as the water pipes are insulated and the pump was a little lower than the pot but indoors.

for diy an oildrum ,a hose to fill it when needed ,some copper pipe and a few fittings to a bath tap and a small pump would be the basic kit ,add a few bricks etc and it could be very cheap to make.

dpack



Joined: 02 Jul 2005
Posts: 45376
Location: yes
PostPosted: Sat May 21, 16 12:56 pm    Post subject: Reply with quote
    

WOW

that is swimming pool size but a similar principle in a rocket stove might be just the thing for a bath

Mutton



Joined: 09 May 2009
Posts: 1508

PostPosted: Sat May 21, 16 4:00 pm    Post subject: Reply with quote
    

Wow on both thanks.

Though on the second one in the barbecue there is the potential for the flame temperature to melt the solder on the pipe joints.

For us - sadly we are in a modern bungalow, timber framed walls, only one chimney - and that is about as far from the bathroom as you can get..........

Hope it helps the OP though.

dpack



Joined: 02 Jul 2005
Posts: 45376
Location: yes
PostPosted: Mon May 23, 16 2:40 pm    Post subject: Reply with quote
    

so long as there is water in the pipes the solder will not melt even if the water turns to steam ,below about 300c it will stay solid although i would not want superheated steam in my bathroom.

Post new topic   Reply to topic    Downsizer Forum Index -> Energy Efficiency and Construction/Major Projects All times are GMT
Page Previous  1, 2
Page 2 of 2
View Latest Posts View Latest Posts

 

Archive
Powered by php-BB © 2001, 2005 php-BB Group
Style by marsjupiter.com, released under GNU (GNU/GPL) license.
Copyright © 2004 marsjupiter.com